Wireless Module Installation

Peel off the battery adhesive, attach the battery inside the enclosure, and connect the ribbon cable.

 

Wireless Module Pairing & Power On/Off

Insert the wireless receiver into the computer’s USB port, then press and hold the “+” button until the indicator starts flashing.

With the main unit powered off, press and hold TURBO, – and HOME simultaneously for 3 seconds to enter wireless pairing mode.

When the receiver indicator turns solid green, the pairing is successful.

Access the Configuration Page

Connect the Type-C cable, then press and hold START + X + Y for about 5 seconds. The device will automatically reboot, and the color display will show “setting”.

Then open a web browser, enter 192.168.7.1, and wait for the browser to automatically refresh. The UI page will be displayed when the connection is successful. (It is recommended to use Google Chrome.)

Button Mapping

Enter the configuration page.

Select the button you want to change, then change it to the desired key on the right side.

Note: Multiple key values can be assigned to a single button.

Button Profile Presets

Remap buttons in the web configurator: Enter the configuration page.

Step 1: Create a new Profile 2 first, then change the corresponding button mappings.

Step 2: Configure the SOCD settings, then switch the profile to the newly created Profile 2.

Save and reboot for the changes to take effect.

Platform Mode Switching

Wireless:

Switch (NS2): With the device powered off, press and hold A + HOME until the device powers on.

PC Mode: With the device powered off, press and hold B + HOME until the device powers on.

PS2/3 Mode: With the device powered off, press and hold X + HOME until the device powers on.

PS5 Mode: With the device powered off, press and hold Y + HOME until the device powers on.

PS4 Mode: With the device powered off, press and hold LB + HOME until the device powers on.

Xbox Mode: With the device powered off, press and hold RB + HOME until the device powers on.

Keyboard Mode: With the device powered off, press and hold RT + HOME until the device  powers on.

 

Uploading and Switching Images

  1. Hold STARTwhile connecting the Type-C cable. The color display will show “Haute Engine Setting”.
  2. Open Google Chrome and visit 168.7.1. Enter the web configuration page, go to Screen Settings, and upload a custom image.
  • Image resolution: 160 × 86
  • Supported formats: JPG, PNG

Save and reboot for the changes to take effect.

  1. Adjust screen brightness: Hold START, then press UPor DOWN to increase or decrease the screen brightness.
  2. Shortcut for switching between image and text display: Hold START +BACK, then press “ ➖“

 

Screen Mode Switching

  1. Press START +BACK + HOME to enter Screen Interaction Mode.

SOCD Mode Switching

The default mode is Neutralize Up.

HOME + START + UP — Up Priority Mode (Left + Right = Neutral, Down + Up = Up) 

HOME + START + DOWN — Neutral Mode (Left + Right = Neutral, Up + Down = Neutral) 

HOME + START + LEFT — Last Input Priority Mode (Left + Right = Right, Up + Down = Down) 

LED Lighting Controls

BACK + START + X — Next animation

BACK + START + A — Previous animation

BACK + START + Y — Increase brightness

BACK + START + B — Decrease brightness

BACK + START + RB — Increase LED parameter

BACK + START + RT — Decrease LED parameter

BACK + START + LB — Increase RGB lighting effect parameter

BACK + START + LT — Decrease RGB lighting effect parameter

Module Replacement

Open the bottom cover, remove the decorative foam, place the corresponding module into the screw holes and tighten the screws, then connect the corresponding ribbon cable.

Internal Storage

The decorative storage compartment can store a USB authentication dongle and a 2.4G wireless receiver.

Palm Rest Replacement

Open the enclosure. There is a round hole on the edge of the back side of the palm rest. Push the palm rest out through the hole.

Button and Switch Replacement

Use the included white pry tool to lift the keycap from the gap around it. Then use the switch puller to grip both sides of the switch and pull it out.

Joystick Restrictor Gate Replacement

Remove the five screws on the restrictor gate, replace the required part, and then tighten the screws.

Joystick Actuator and Spring Replacement

After removing the restrictor gate, use the included “retaining clip tool” or a flat-head screwdriver to push out the joystick retaining clip. Then replace the desired actuator and spring.

After the replacement is complete, use the “retaining clip tool” or a pair of pliers to reinstall the retaining clip.

Installation Method for End Caps